F-linX
Automation rangeSteel-Line's automation and control line, supplied with its doors.
Openers by make · Perth
Steel-Line Garage Door Motors and F-linX Automation in Perth
The automation that comes with Australia's biggest door range. Roller, sectional and tilt drives all serviced by the same crew that works on the door.
- F-linX automation
- We supply & install
- Remotes coded on site
- All Perth suburbs
Steel-Line
- Origin
- Australia
- Known for
- F-linX automation
- Door types
- Roller, sectional, tilt & commercial
- Fitted with
- Steel-Line doors
- What we do
- Supply, install, service & repair
New units fitted, old ones fixedMaker’s website
Steel-Line garage door openers and F-linX automation are serviced, repaired and replaced across Perth by our technicians. Because Steel-Line makes roller, sectional and tilt doors, the drive on your door depends entirely on which type you have — we identify it on site and quote the actual work rather than a generic opener repair.
Not a Steel-Line? The full list of motor makes we work on around Perth covers the rest. Product details are on Steel-Line’s own website.
Three Door Types, Three Different Drives
Steel-Line is Australia's largest door manufacturer and supplies automation under the F-linX name alongside its doors. Because the door catalogue spans roller, sectional and tilt, the opener on a Steel-Line door is not one thing: a roller drive beside a drum, a rail drive above a panel-lift door and a tilt door's drive are three different machines with three different failure modes.
That matters when you ring. "My Steel-Line motor has stopped" tells us less than "my roller door motor has stopped", and the second version is what lets us plan the right part. If you are unsure, a photo of the head unit and one of the door from inside answers it instantly.
The faults themselves are ordinary. Travel and force limits drift over the years and a door starts stopping short or pressing hard at the floor. Capacitors and gears wear, particularly on a drive that has been fighting a door with tired springs. Remotes lose their pairing, and our guide to programming a Steel-Line remote covers re-coding one. All of that is repairable, and we check the door's balance before deciding the drive is at fault.
Jobs we take on
Work we do on Steel-Line gear
Models
Which Steel-Line have you got?
Match the name on your unit's sticker to one of these cards.
Faults
Faults we find on Steel-Line units
Pick the symptom you are seeing to read the likely causes and the fix.
Fix or swap
Keep the Steel-Line going, or retire it?
The same yardstick we use on our own openers. A repair comes first whenever the unit has life left in it.
Worth fixing if…
- The fault is a limit setting, a gear, a capacitor, a sensor or a remote — the everyday opener repair list.
- The drive runs cleanly once the door has been re-balanced.
- Parts are still available for the unit's age and range.
- You need remotes, a wall button or a keypad paired.
Time to replace if…
- The board has failed on a drive that is no longer supported.
- The unit has been hauling an unbalanced door long enough to wear through.
- The opener is underrated for a heavy insulated or custom-faced door.
- You want a quieter drive or controls the current one cannot provide — compare the openers we fit.
Choosing the next opener
A new motor is sized to your door: roller, sectional or tilt, and how heavy it is. Most people end up with a belt drive for the quiet running, and most current units can be run from a phone as well as a remote. We take the old motor away.
Before it goes up, the door is balanced by hand. An opener dragging a badly tensioned door burns out early, so the springs get sorted first.
Openers we installPricing
What sets the price on a Steel-Line motor job
Steel-Line opener work is priced on the door type and the fault. A limit re-set or a remote is the light end; a gear or capacitor is the middle; a board or a replacement drive is the top. If the door is the underlying cause, that is quoted as door work.
Your quote depends on
- Roller, sectional or tilt — three different drives
- Whether it is a setting, a wear part or the board
- Door weight, particularly on custom or insulated faces
- Whether the springs or counterbalance need setting first
Get your Steel-Line motor job priced
Questions
Asked about Steel-Line motors
Wrong make?
More motor makes we look after
Check the badge or sticker, then jump to the matching page.
Also useful
Other jobs and how-tos
Coverage
Suburbs we drive to for Steel-Line work
Give us your suburb when you ring and we will book a time that suits you.
Tell us whether the door is a roller, a sectional or a tilt — that single detail decides which drive we bring parts for.
Get a quote
Book Steel-Line motor work in Perth
Owner-run and based in Perth. Fill in the form with what the door is doing and we will come back with a price, or ring and talk it through.
- 0422 828 800
- , Bennett Springs WA
- Mon–Fri12 AM – 11:59 PMSat–Sun12 AM – 11:59 PM